All Products ( 142 Items )

135 deg. split point works great for aluminum

Sold individually. 100 degree, 3-flute. 1/2" Body Diameter. 1/4-28 threaded shank. Use with micro stop units (CT-196, CT-360& CT-365). A new, high quality cutter.  CC40 - #40 drill size for...

Use to enlarge rivet holes on prepunched kits. Work better than drill bits. Maintain self in center. Enlarge holes cleanly. Less deburring required.  

Used to set flush side of flush rivets. 1/8" body length x 1/2" diameter. Made from 17-4 stainless steel. 3/16" shank for inserting into standard tooling. Flat "set" refers to...

Select sizes needed via the drop down menu, one at a time. This size required for Van's RV kits. 426-3 426-4 See also screw sizes for #6 and #8 screws...

Cobalt jobber drill. 135 degree split point. Works great for aluminum.  

Starting your Van's RV tail kit? Order: Qty 10-3/16"Qty 50- 1/8"Qty 150-3/32"  Spring-loaded plunger type fasteners used to hold drilled components together tightly prior to riveting. Operated using cleko pliers. Steel bodies...

This size required for Van's RV kits. 509-6 509-8 See also -3 and -4 Rivet Sizes Spring back angle on both die faces. Minimizes skin deformation. Skins remain very flat!...

12" Long cobalt drill. Keeps the drill away from your work. Helps drill those hard to reach areas. 135 deg. split point. Works great for aluminum.

Cobalt jobber drill. 135 degree split point. Works great for aluminum.  

Spring loaded plunger type clamp fasteners operated using cleko pliers. 1" deep jaws (available in 1/2" deep jaws). Useful for holding sheets to ribs or bulkheads prior to drilling. Good...

  This set is the second from the left as shown in the photo. Cup sets used in hand or pneumatic squeezer. Cup shaped to fit AN470 Universal Head Rivets....

Cobalt extension drill. 6" Long for getting the drill away from your work. Helps drill those hard to reach areas. 135 deg. split point works great for aluminum.

Deburring bit with hex shank fits into a cordless screw driver.  100 degree, one-hole chatterless deburring bit with intergral 1/4" hex shank. A cordless screwdriver is very controllable and makes...

Gauge measures -3, -4, -5 and -6 universal head and flush rivets. Used to check proper length of exposed rivet shank BEFORE setting. Used to check proper length and width...

Close quarters die allow access to holes where there is not clearance for a squeezer or c-frame. Just what you need for tight spots. Pull die mandrel with pop riveting...

This is a tool that REALLY WORKS!  Roller shape forms a slightly turned edge on aluminum to assure a tight fit along the joints of overlapping sheets.  Hardened stainless rollers...

Aluminum handle with telescoping blade holder. DBB-10 & DBB-20 blades are included. Blades store in the handle. Additional blades available: Hooked blade (DBB-15). V-blade for edges (DBB-70). Made in Isreal...

Our basic countersink cage.Rated at 3000 RPM.1/4"-28 threaded shaft..001" increment depth adjustment with threaded lock.9/32" shaft travel.5/8" diameter cutter capacity.1/4" diameter shank.Standard type skirt.Does not have a nylon foot. 

Scotch Brite Cutting and Polishing Unitized Wheel, 7A Medium. Long lasting, aggressive for tough deburring and polishing. Use to deburr and radius edges.  Blends and polishes.  Will not load up...

Nickel plated pliers. Use for installation and removal of brand fastener types: Cleko-Loc Kwik-Loc Monogram (Wedge-Loc)  Fits all sizes of clekos and cleko clamps.

General purpose Scotch Brite hand pads. Used for cleaning and deburring.  Color- Red 6" x 9" sheet Cut to size for hand use in mini mandrel.

Flute flanges between rivet holes to flatten ribs and bulkheads. Protruding jaw spaces the beginning of the flute back from the proper distance from the web. Makes nice narrow flutes-...

1/2" dia. flush set with slim DELRIN spring tension sleeve. Length of 3.5". Used for setting flush rivets from the back side. Tension sleeve safely holds both layers of aluminum...

Scotch Brite Cutting and Polishing Unitized Wheel, 7A Medium. Long lasting, aggressive for tough deburring and polishing. Use to deburr and radius edges.  Blends and polishes.  Will not load up...

3" Reach Yoke. Recommended size for RV's.  Made from 4140 steel.  Heat treated prior to machining to eliminate warping. The varied yoke designs expand the usefulness of the pneumatic squeezer....

Offset design features angled jaws so handles will clear work.  Use for straightening and aligning fittings and rib flanges. Angled jaws allow tool clearance when adjusting rib flanges in the...

Don't mistake lower cost bits as the same quality as these.  Colbalt high-speed steel (not carbide) = longer life, lower cost per tool.  1/4"-28 thread drill bits. Standard 1-1/4 long....

Stubby 2-1/16" mushroom flush set with .401" dia. shank. The 1" dia. face is highly polished. This is the ideal size for setting 3/32" & 1/8" flush head rivets. US...

Leave the heavy rubber hose and coupler on the floor!Kit Contains: 10' Lightweight Very Flexible Air Hose Miniature Coupler ¼”NPT Male Threaded End 3 Mini Plugs (to connect to your...

True Vixen brand files made by Simons were widely recognized as the most efficient ever designed for aluminum and fiberglass however, Simons is no longer producing the Vixen file. We...

4" x 16" x 1/4" Blanchard ground back rivet plate. Used for setting flush rivets from the back side. Perfect for riveting control surfaces. Cut a 4" x 16" hole...

Single cutting edge creates perfectly round holes. Can be used on metal, plastic and other thin materials.  Each step is marked for easy hole size selection. Made of high speed...

 Screws to workbench.  Overhangs enough to allow rib flange to slide over.  Machined springback 3/32" (#40) female die built in.  Use standard 3/32" male die in rivet gun set or C-frame...

Scotch Brite Cutting and Polishing Unitized Wheel, 7A Medium. Long lasting, aggressive for tough deburring and polishing. Use to deburr and radius edges.  Blends and polishes.  Will not load up...

1/8" cup set - straight 3.5". Cupped set used for setting AN470 universal head rivets. Precision ground .401" shanks.

Used on the rivet gun to control the strength of blow. Adjust when changing from one size of rivet to another. Swivel has 1/4 turn full on to full off...

1/8" cup set - double offset 5.5". Cupped set used for setting AN470 universal head rivets. Precision ground .401" shanks. Double offset shank allows reaching rivets in restricted areas.

Screw on mandrel for 1" Scotch Brite wheels (3MW-7A1 and 3MW-2S1).  Screws into a 3/16" hole. 1/4" chucking shank. 

Lightweight hand squeezer for dimpling skins and squeezing rivets30% Lighter Weight, 65% Less Effort Required!  This squeezer outperforms all other squeezers on the market. As with all of the tools...

Designed to maintain desired angle while countersinking the trailing wedge found in various Van's aircraft kits including models RV7, 9, 10, and 14. The drill jig is designed for wedge strips...

This Pneumatic Squeezer is manufactured in the US using all new components.  Now INCLUDES the Adjustable Set Holder, no shim washers or changing sets. All moving parts are heat treated...

2.8 lb custom bar. Special Bucking Bar called for in the RV-10 Emp. manual Page 9-12 @ RV-14 manual Page 09-17 for dimensions and 09-20 for use. Machined finish is...

Taylor Rivet Guns Feature: 3X Gun- up to (very short) 3/16" rivet capacity. Extra sensitive teasing throttle for full control. Hardened tool steel piston & alloy steel cylinder for long...

The Ultimate in Bucking Bars Small Tungsten Bucking Bar  Weighs 1.58 lbs. (heavier than most bars twice this size). Measures 5/8" x 1" x 4" Slight angle on one end...

3/32" cup set - straight 3.5". Cupped set used for setting AN470 universal head rivets. Precision ground .401" shanks.

Single flute won't leave wavy chatter marks in the bottom of the countersink like the 3-flute will. Single flute are much more aggressive, do not push on them like the...

4000 RPM 1/4 Chuck and Key Fine Feathering Trigger Allows Operator Complete Control of Drilling Speed 360 Degree Rotatable Exhaust Air Inlet 1/4-18 NPT 1.48 Lbs. Smooth Quiet Operation   ...

Mandrel for 3/4" wide 2" wheel.  1/4" shank.  Threads screw into 1/4" hole in wheel. Use with 3MW-7A2S.

Scotch Brite Light Deburring Wheels are designed for removing burrs and polishing at the same time. Excellent for fine deburring and polishing operations. Blends and polishes.  Will not load up...

Manufacturer manages shipping. We post any known ship delay info here. If no delay is mentioned, you can expect shipping within 5 business days.    DRDT-2  (Dash 2) is a welded steel...

2.5" Flange Nose Yoke.  Download Dimensions Designed to reach over flanges or longerons. Made from 4140 steel.  Heat treated prior to machining to eliminate warping. The varied yoke designs expand...

Carbide V-shaped blade for deburring edges of aluminum sheets up to 1/8 thick.  Fits DBS-33 handle. Carbide tipped. Deburrs sheetmetal up to 0.14" (3.5 mm) thick. Q :   I...

C-FRAME TOOL:  A combination of the best features of several tools. Set holder in base features .401" shank and can also be used in rivet gun Base accepts all .401"...

This nifty little tool works much like the countersink cage.  Interchangeable collars center over universal head rivets while the bit drills out the center.  Included are #40, #30, #21 and...

2.8 lb back riveting bar. Hardened and ground. Several polished surfaces. Use the surface that allows the bar to be held firmly, flush to the rivet stem and perpendicular to...

1/2" dia. flush set with slim DELRIN spring tension sleeve. Used for setting flush rivets from the back side. Tension sleeve safely holds both layers of aluminum tightly together while...

Designed for RV-12 rivets that get pulled in close quarter or corner applications. Manufactured by Avery Tools from 1/4" x 3/8" steel bar. Length 4" long. Turned up angle at...

Scotch Brite Light Deburring Wheels are designed for removing burrs and polishing at the same time. Excellent for fine deburring and polishing operations. 3M Grade 2SFn Blends and polishes.  Will...

Tape holds rivets in position while back riveting. Scotch Magic REMOVABLE Tape is easily removed. Similar to Post-It Notes adhesive. For use with flush rivets. For universal head rivets use...

Spring back angle on both die faces. Minimizes skin deformation. Skins remain very flat! Precision manufactured on our CNC machine. Stainless Steel - Heat treated. Polished dimpling surfaces. Don't make...

Avery Tools designed and manufactured. Swivel action - makes deburr & c’sink holes fast & easy. Molded handle with 2” long plated steel shaft with 1/4”-28 threaded holder. Includes (1)...

Approximately 5 ½" X 4 ½ X 1 ½" clear acrylic 28 Holes to Organize Dimple Dies and Flat Sets

Includes: NAS 1097 AD 4 - 3.5NAS1097  AD 4 - 4NAS 1097 AD 4 - 5NAS 1097 AD 3 - 3NAS 1097 AD 3 - 3.5NAS 1097 AD 3 - 4

Quick Release Yoke Pins allow yokes to be changed quickly and easily. Work with the Pneumatic Squeezer or The Main Squeeze.

Mini plug on one end and 1/4" male pipe thread on the other. Rectus couplers are very high quality and are German made. Their superior flow characteristics result in lower...

Now when you go to a fly-in and park that beautiful airplane you no longer have to thread in an ugly tie down ring.This annealed stainless tie down ring looks...

Mandrel holds rectangles of Scotch-Brite hand pad (3MP-47). Chucked in a drill, works like a flap wheel to deburr tubing and irregular shaped edges. 3" long with 1/4" shank.

4" Thin Nose Yoke. Thin nose design to reach in tight places. Used to squeeze rivets only, will not accept dimple dies.  Made from 4140 steel.  Heat treated prior to...

An upgraded cage because of the nylon foot.Rated at 3,000 RPM1/4" Diameter Chucking Shank9/32" Shaft Travel5/8" Cutter Capacity1/4-28 Threaded ShaftNylon Threaded No-Mar Foot PieceOutside Bottom Diameter: 1.008 Inches

Manifold Block mounts to bench or wall providing multiple outlets for tools. Your existing large rubber air hose connects to manifold to supply air. Very flexible, lightweight hoses with miniature...

Same piece that comes with our C-Frame. Allows you to hold die in rivet gun. Perfect for use with DIE4263DF

Double offset version of our extended back rivet set. This set allows rivet gun to be offset, however it is more difficult to drive rivets than the straight version. Spring...

This rivet set retaining spring makes changing sets quick and easy. Change sets without removing spring. Perfect for setting AN rivets in aluminum sheet with 2X, 3X, or 4X rivet...

This blade fits into the DBS-33 deburring handle.  For plastic or soft materials. Simultaneously deburrs the inside and outside of holes up to 0.16" (4 mm) thick.   

Pneumatic Rivet Puller is the right tool when installing large numbers of pop rivets. Reduces strain on forearms and wrists. Interchangeable nose pieces included. Replacement jaws available. Pulls 4 sizes...

2.2 lb footed bar fits in tight places. Hardened and ground. Several polished surfaces. Use the surface that allows the bar to be held firmly, flush to the rivet stem...

This blade fits into the DBS-33 deburring handle.  For Aluminum or Steel. HSS. Deburrs materials with spiral chips.   

4" Reach Yoke.  Made from 4140 steel.  Heat treated prior to machining to eliminate warping. The varied yoke designs expand the usefulness of the pneumatic squeezer. Allow hard to reach...

Cleaveland Aircraft Tool's T-Shirt Show your support at air shows and local meetings.

1" Thin Nose Yoke. Thin nose design to reach in tight places. Used to squeeze rivets only, will not accept dimple dies.  Made from 4140 steel.  Heat treated prior to...

Adjustable length ram eliminates the need for shim washers and various length sets.  When using with 1.25" thick yoke bases or longeron yoke use a 1/2" long flat set or...

2.5" Thin Nose Yoke. Thin nose design to reach in tight places. Used to squeeze rivets only, will not accept dimple dies.  Made from 4140 steel.  Heat treated prior to...

3 Inch cut-off disc with 1/4 inch center hole. Used for cutting thin walled tubing, sheet metal, fiberglass or for slotting applications. Use to cut off excess from canopy. Maximum...

Mini coupler brass fitting with female fitting on one end and 1/4" male pipe thread on the other. Rectus couplers are very high quality and are German made. Their superior...

Shipping in January Our exclusive hand squeezer is delayed in production. See the linked handle for details.  Kit Contains: Main Squeeze Handle  (See here for further details) 3" Yoke (same...

  Vinyl covered wire snap-on trim for trailing edge of glare shield. U-shaped strip 0.52" wide x 0.39" thick x 54" long. Accomodates up to 1/16" thick edge. For all...

Due to supply chain delays (including access to raw materials) shipping times for this product are longer than normal. We are annoyed too, trust us. For U.S. customers, other items in order...

1" diameter bushing for reducing the hole of wheels from 1" to 5/8".